How to Paint Textured Walls

To paint a textured wall, use a roller with a thicker nap, ½ inch for orange peel and knockdown or ¾ inch for heavy textures, load it well, and roll in overlapping passes from more than one direction so the paint reaches into every dip. Plan on more paint than for a smooth wall: about 300 square feet per gallon for light textures and closer to 250 for heavy ones, instead of the usual 350.
Texture is great at hiding dents and seams, which is why so many North American homes have it. It’s also why painting it takes a little more paint, a different roller, and a slightly different rolling habit.
Nap and coverage by texture type
| Texture | What it looks like | Roller nap | Coverage we use | Extra paint vs smooth |
|---|---|---|---|---|
| Smooth (level 5 finish) | Flat, no pattern | ⅓ to ⅜ inch | 350–400 sq ft/gal | — |
| Orange peel | Fine bumps, like citrus skin | ⅜ to ½ inch | 300 sq ft/gal | About 15% |
| Knockdown | Flattened splatter, mottled | ½ inch | 300 sq ft/gal | About 15% |
| Skip trowel, heavy hand texture | Raised, irregular trowel marks | ¾ inch | 250 sq ft/gal | About 40% |
| Popcorn (ceilings) | Lumpy, cottage-cheese texture | ¾ inch or thicker | 200 sq ft/gal | About 75% |
The coverage figures are the planning rates our calculators use, inside the 250 to 400 square feet per gallon range that manufacturers such as Behr give for one coat. Your paint can and your wall will decide the exact number, so treat these as a sensible starting point.
How much paint for a textured room?
Take an average 12 × 12 ft bedroom with 8 ft walls, one door and two windows: 334 square feet of wall. With two coats and 10% for waste:
| Wall finish | Paint for 2 coats | What to buy |
|---|---|---|
| Smooth | 2.1 gal | 2 gallons + 1 quart |
| Orange peel or knockdown | 2.4 gal | 2 gallons + 2 quarts |
| Heavy texture | 2.9 gal | 3 gallons |
The paint calculator has a “textured or knockdown” setting that applies this automatically, and our guide on how much paint you need for a room explains the rest of the math.
How to roll a textured wall
- Clean it. Texture traps dust, cobwebs and grease in every hollow. Vacuum the wall with a brush attachment, then wipe it with a damp sponge.
- Cut in generously. A brush skips over the high points along edges, so work the paint into the texture with a slight stippling or dabbing motion and make the band a little wider than usual.
- Load the roller fully. Thick naps hold a lot of paint. Roll it in the tray until it’s saturated but not dripping, and reload more often than you would on a smooth wall.
- Roll in more than one direction. Lay the paint on with a W pattern, then roll across it and finish with light vertical passes. Changing direction pushes paint into both sides of every bump. Look at the wall from an angle: tiny unpainted pinholes in the dips mean you need more paint on the roller or another pass.
- Keep a wet edge. Textured walls hide lap marks a little better than smooth ones, but rolling into half-dry paint still shows. Finish each wall without stopping.
- Don’t press hard. Pressure squeezes paint out of the nap onto the high points and leaves the hollows bare. Let a well-loaded roller do the work.
Do textured walls need primer?
Only in the same situations as smooth walls. A textured wall that’s already painted and in good shape can go straight to paint. New texture is different: it’s made of joint compound, which is very absorbent, so fresh texture needs a coat of drywall primer or the paint will dry blotchy. The same goes for patches where texture has been repaired. Our guide to whether you need primer covers every case, and the primer calculator works out the amount.
How to patch a textured wall before painting
A smooth patch in the middle of a textured wall stands out more than the hole did. After filling and sanding the repair, recreate the texture before you prime:
- Orange peel: spray texture in an aerosol can, sold in light and heavy patterns, matches it well. Practise on cardboard first and build it up in thin passes.
- Knockdown: spray the texture, wait a few minutes until it starts to set, then flatten it lightly with a wide drywall knife.
- Heavier hand textures: dab or trowel thinned joint compound onto the patch with a sponge or knife to copy the pattern around it.
Let the texture dry fully, prime it, and then paint the whole wall rather than just the patch. Touching up only the patch almost always shows as a different sheen.
Which sheen works best on textured walls?
Flat and matte finishes are the most forgiving. They don’t reflect light from the peaks of the texture, so the wall looks even, and touch-ups blend in well. Eggshell is a good middle ground for living areas and bedrooms that get some wear. Satin and glossier finishes make texture look more pronounced, because each bump catches the light; that can look attractive in a bathroom or kitchen, but it also exaggerates any unevenness in the paint.
Should you spray textured walls?
Spraying is very good at getting paint into heavy textures and popcorn ceilings, which a roller can struggle with. The trade-off is the usual one: heavy masking and more paint lost to overspray. A common compromise is to spray, then back-roll with a thick-nap roller, which pushes the paint in and evens out the coat. Our comparison of rollers, brushes and sprayers goes into more detail.
A note on popcorn ceilings
Popcorn is a ceiling texture rather than a wall texture, but it raises the same questions. It soaks up a lot of paint, roughly 200 square feet per gallon, and it softens when wet, so roll it gently in one pass per area and don’t go back over damp paint or chunks may come loose. The ceiling paint calculator has a popcorn setting. In homes built before the mid-1980s, popcorn and some other textures may contain asbestos; have them tested before sanding, scraping or removing them.
Touching up a textured wall later
Touch-ups are harder on texture than on smooth walls, because a brush lays paint on the peaks and skips the valleys, so the patch looks flatter and shinier than the wall around it. A few things help:
- Use the same tool that painted the wall. Dab the touch-up with a small roller of the same nap, not a brush, so the texture of the paint film matches.
- Feather the edges. Roll outward from the spot with an almost dry roller so the new paint fades into the old.
- Use leftover paint from the same can, stirred well. Even the same color mixed months later can differ slightly.
- Expect flatter sheens to blend best. On satin or semi-gloss texture, repainting the wall from corner to corner is often the only invisible fix.
Painting textured walls a dark or deep color
Deep colors on texture look rich and dramatic, but they make thin spots and pinholes much more visible. Plan for these differences:
- Prime with a tinted primer close to the final color, so any pinholes the paint misses don’t flash white.
- Plan for three coats on heavy texture; deep-base paints hide less per coat.
- Back-roll in two directions on every coat to push paint into the hollows.
- Inspect with a flashlight held flat to the wall after each coat, and fix pinholes while you still have paint on the roller.
Should you skim-coat texture smooth instead?
Some homeowners decide they’d rather have smooth walls. Skim-coating, troweling thin layers of joint compound over the texture and sanding them flat, can do it, but it’s slow, dusty work that takes several coats and days of drying per room, and getting a truly flat finish takes practice. For most people it’s a job for a drywall finisher. If you only dislike how the texture looks under paint, a flatter sheen often solves the problem for a fraction of the effort.
Frequently asked questions
What roller nap is best for textured walls?
A ½ inch nap for orange peel and knockdown, and ¾ inch for heavier hand textures. Thicker naps carry more paint into the dips.
How much more paint do textured walls need?
About 15 to 20% more for light textures like orange peel and knockdown, and around 40% more for heavy textures, compared with a smooth wall.
Why are there tiny white spots in my paint on a textured wall?
Those are pinholes where the paint didn’t reach the bottom of the texture. Load the roller more fully and roll from more than one direction, or dab the spots with a brush.
Can you paint textured walls with a brush?
Only the edges. Brushing a whole textured wall is slow and leaves thin spots on the high points. Use a thick-nap roller or a sprayer.
Does texture hide imperfections?
Yes, that’s one of its main purposes. Texture breaks up light, so small dents, seams and repairs are much less visible than on a smooth wall.
Should I paint textured walls flat or eggshell?
Flat or matte hides texture variations best. Eggshell is a good choice in busier rooms where you want a wipeable finish.
Sources
- Behr, How much paint do I need?: 250–400 sq ft per gallon per coat, depending on the surface.
- Amounts: Brushwright calculation, 334 sq ft of wall, two coats, plus 10%.
Estimates only. The coverage printed on your paint can and the product instructions are the numbers to trust.