How to Paint Interior Doors

How to Paint Interior Doors

To paint an interior door, take it off its hinges if you can and lay it flat on sawhorses, remove the hardware, clean and lightly scuff-sand it, fill dents, and prime bare wood or old oil-based paint. Then paint in a set order: on a panel door, the recessed panels first, then the center stile, the horizontal rails and finally the outer stiles and edges, using two thin coats of a semi-gloss or satin trim enamel. Let each coat dry fully and don’t close the door until the paint has hardened.

A door is the most handled painted surface in a house, which is why it needs a harder paint and more patience than a wall. The order of strokes matters too: it’s what stops overlapping brush marks and drips from showing on the finished door.

The facts
PaintSemi-gloss or satin trim enamel
Paint per standard door, both sides, 2 coatsAbout 0.2 gallons: a quart per door
Best setupDoor off its hinges, flat on sawhorses
Before closing the doorWait until the paint has hardened, not just dried to the touch

Should you take the door off to paint it?

Method Pros Cons
Off the hinges, laid flat No drips or sags, smoothest finish, easier to reach every edge You need space, sawhorses and time to dry each side
In place, hanging Quick, no lifting or rehanging Paint can run on vertical surfaces; hinges and floor need careful protection

For the best finish, especially with glossy paint, take the door down. Tap the hinge pins up and out with a nail set or a screwdriver and a hammer, starting with the bottom hinge, while someone steadies the door. Label each door and its frame with a piece of tape so they go back to the same opening.

If you’re painting many doors in place, it works fine with lighter coats and careful brushing; just check for drips on the lower panels a few minutes after each section.

How much paint for interior doors?

A standard 30 × 80 inch interior door is about 17 square feet per side, or about 35 square feet including both faces and the edges. Two coats of trim enamel at about 400 square feet per gallon, plus 10%:

Doors Paint, 2 coats What to buy
1 door, both sides About 0.2 gal 1 quart
4 doors About 0.8 gal 1 gallon
10 doors About 1.9 gal 2 gallons

Panel doors have slightly more surface than flat slab doors, and the casings around each door add more; if you’re painting casings in the same color, add about a quart for every few doors. If you’re painting the baseboards too, see our guide to painting baseboards for their amounts.

What paint is best for doors?

Doors need a trim enamel: a paint designed to level out smoothly and cure hard, so hands, bumps and cleaning don’t mark it. Water-based and hybrid (water-based alkyd) enamels give a smooth finish without the yellowing and long drying of traditional oil-based paint. Semi-gloss is the classic sheen; satin is a softer-looking, slightly more forgiving alternative. Our guide to latex vs oil-based paint explains the options, and our guide to paint sheens covers the trade-offs.

What you’ll need

  • Screwdriver, nail set or long nail, hammer, and labeled bags for hardware
  • Two sawhorses and painter’s pyramids or a few scrap blocks to raise the door
  • Degreasing cleaner, sponge, wood filler, 180 and 220 grit sanding sponges
  • Primer (bonding primer for old oil paint or glossy surfaces, stain-blocking for bare wood with knots)
  • Semi-gloss or satin trim enamel
  • A 2 to 2½ inch angled brush, a small 4 to 6 inch foam or fine microfiber roller
  • Painter’s tape for hinges and glass, and drop cloths

Step 1: Remove hardware and clean

Take off the knob or lever, the latch plate and the strike, or tape them carefully if they’re difficult to remove. Hands leave oil around the handle and on the edge of the door, so wash the whole door with a degreasing cleaner, paying attention to the area around the handle and the latch edge. Rinse and let it dry.

Step 2: Test, repair and sand

Test the existing paint with a cotton ball dampened with rubbing alcohol. If no color comes off, it’s likely oil-based, and it needs a bonding primer before water-based paint. In older homes, test for lead before sanding.

Fill dents and dings with wood filler, let it dry and sand it smooth. Then scuff-sand the whole door with a 220-grit sanding sponge to dull the gloss so the new paint grips. Remove the dust with a vacuum and a damp cloth.

Step 3: Prime

Prime any bare wood, filled areas and old oil-based or glossy paint. A door in good condition with sound latex paint in a similar color usually needs only spot-priming. If you’re making a big color change, such as white to black or the reverse, a tinted primer saves a coat.

The painting order for a panel door

Painting in the right order means each section is brushed before its neighbors, and brush marks follow the direction of the wood grain:

  1. The recessed panels. Paint the molded edges of each panel first with the tip of the brush, then the flat panel, finishing with light strokes in the direction of the panel’s grain.
  2. The center stile, the vertical piece between the panels, top to bottom.
  3. The horizontal rails: top, middle and bottom, brushing side to side.
  4. The outer stiles, the long vertical pieces on each side, full length top to bottom.
  5. The edges, if you’re painting them with this side’s color.

Work quickly enough that each section is still wet when you blend the next one into it, and wipe any paint that pools in the panel corners before it sets.

How to paint a flat (slab) door

Flat doors are easiest with a small foam or fine microfiber roller. Roll a thin, even coat over the whole face, then “tip off” the wet paint with one long, very light brush stroke from top to bottom, the full height of the door. Tipping off removes the slight roller texture and leaves a smooth, brush-like finish. Do the edges with the brush.

Which color goes on the door edges?

When the two sides of a door are different colors, painters follow a simple convention so that when the door is open, each room sees only its own color:

  • The latch edge (the edge with the knob) gets the color of the side that faces into the room the door opens into.
  • The hinge edge gets the color of the other side.

If both sides are the same color, paint all the edges that color. The top and bottom edges aren’t seen, but sealing them with a coat of primer or paint helps keep the door from absorbing moisture unevenly, especially in bathrooms.

Drying, flipping and rehanging

With the door flat, let the first side dry to the touch, then apply its second coat. Once the second coat on that side has dried as long as the label says, flip the door carefully onto pyramids or clean blocks and paint the other side. Don’t rush the flip; enamel that feels dry can still mark.

Rehang the door only when the paint has hardened enough not to be marked by handling, then reinstall the hardware. For the first days, leave the door slightly open rather than closing it hard against the stop, where soft paint can stick to the frame. Small clear bumper pads on the stop help.

Enamels keep hardening for days to weeks, which is normal; our article on how long to wait between coats explains drying and curing.

Doors with glass

For French doors and doors with glass panes, tape the glass at the edges with painter’s tape, or paint over the edge of the glass slightly and scrape the excess off with a razor scraper once the paint has dried. A narrow angled brush is the right tool for the muntins, the thin strips between panes.

Closet and bifold doors

Bifold and sliding closet doors can usually be lifted out of their tracks. Paint them flat like any other door, and paint the louvers on louvered doors with a small brush, or spray them, since brushing every slat is slow and tends to drip. Let them cure before putting them back, because they rub against each other when folded.

Colors for interior doors

The traditional choice is the same white as the trim, which keeps the house calm and consistent. Painting doors a contrasting color, such as charcoal, black, deep green or navy, is a popular way to add character without painting whole rooms; deep colors hide fingerprints well but need a tinted primer and careful prep. Painting doors and trim the same color as the walls, in a glossier sheen, makes doors recede and suits minimalist rooms.

Mistakes to avoid

  • Painting over the hinges. It looks sloppy and the hinges stop moving freely. Remove or mask them.
  • Thick coats. They run on vertical doors and stay soft. Two thin coats beat one thick one.
  • Overbrushing. Going back over enamel as it starts to set leaves drag marks; lay it on and leave it.
  • Closing the door too soon. Fresh enamel sticks to the frame and peels.
  • Skipping the sanding. Glossy old paint without a scuff or a bonding primer can scratch off.
  • Mixing up doors. Label each door and frame before taking them down.

How long does it take?

Plan on about an hour of prep per door, plus primer drying time, and about 30 to 45 minutes per side per coat for a panel door. Painting several doors at once is more efficient: while one side of each dries, you can work on the next door. A batch of four to six doors makes a good weekend project.

Frequently asked questions

What is the best paint for interior doors?

A semi-gloss or satin trim enamel, water-based or hybrid. It levels smoothly, cures hard and is easy to clean.

Is it better to paint a door on or off the hinges?

Off the hinges, laid flat, gives the smoothest finish with no runs. Painting in place is quicker and works with thin coats and careful brushing.

How do you paint a door without brush marks?

Use a quality enamel that levels, thin coats, a good brush, the correct painting order, and finish each section with one long, light stroke. On flat doors, roll then tip off with a brush.

Do I need to sand a door before painting?

A light scuff-sanding with fine grit is recommended so the new paint grips, especially over glossy paint. You don’t need to strip it.

How long should paint dry before closing a door?

Until it’s hard enough not to stick, often a day or more for trim enamels. Leave the door slightly ajar or add bumper pads for the first days.

How much paint do I need for a door?

About a quart for both sides of a standard interior door with two coats. A gallon covers about four or five doors.

Sources

  • Method: standard trade practice for painting interior doors; follow primer and enamel labels.
  • Amounts: Brushwright calculation, about 35 sq ft per standard door, 400 sq ft per gallon, two coats plus 10%.

Estimates only. The coverage printed on your paint can and the product instructions are the numbers to trust.